LS-GL/uboot の変更点

追加された行はこの色です。
削除された行はこの色です。
LS-GL/uboot へ行く。
LS-GL/uboot の差分を削除
[[FrontPage]]
#navi(../)


*LS-GL(Debian lenny)Boot sequence [#e16d2594]
 Orion1   CPU =  Low
 
 === BUFFALO LS-GL U-Boot. ===
  ** LOADER **
  ** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE (CFG_ENV_ADDR=fffff000)
 
 
 U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY
 
 DRAM CS[0] base 0x00000000   size 128MB
 DRAM Total size 128MB
 [256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
 Flash: 256 kB
 Addresses 20M - 0M are saved for the U-Boot usage.
 Mem malloc Initialization (20M - 16M): Done
 
 Soc: 88F5182 A2
 CPU: ARM926 (Rev 0) running @ 400Mhz
 Orion 1 streaming disabled
 SysClock = 200Mhz , TClock = 166Mhz
 
 
 USB 0: host mode
 USB 1: host mode
 PCI 0: PCI Express Root Complex Interface
 PCI 1: Conventional PCI, speed = 33000000
 Net:   egiga0 [PRIME]
 Using 88E1118 phy
 
 Marvell Serial ATA Adapter
 Integrated Sata device found
   Device 0: OK
 Model: ST3750640AS                              Firm: 3.AAD    Ser#:             5QD1MGW5
             Type: Hard Disk
             Supports 48-bit addressing
             Capacity: 715404.8 MB = 698.6 GB (1465149168 x 512)
 
 Using device ide0, partition 1
 
 Loading from block device ide device 0, partition 1: Name: hda1
   Type: U-Boot  File:/initrd.buffalo
 
 2322728 bytes read
 Using device ide1, partition 1
 ** Bad partition 1 **
 Booting from Device 0
 hit any key to switch tftp boot.
 Hit any key to stop autoboot:  0
 Hit any key to stop autoboot:  0
 
 Reset IDE:
 Marvell Serial ATA Adapter
 Integrated Sata device found
   Device 0: OK
 Model: ST3750640AS                              Firm: 3.AAD    Ser#:             5QD1MGW5
             Type: Hard Disk
             Supports 48-bit addressing
             Capacity: 715404.8 MB = 698.6 GB (1465149168 x 512)
 
 Using device ide0, partition 1
 
 Loading from block device ide device 0, partition 1: Name: hda1
   Type: U-Boot  File:/uImage
 
 1813332 bytes read
 <<stop_sound>>
 ## Booting image at 00100000 ...
    Image Name:   linux
    Created:      2009-07-28  16:45:46 UTC
    Image Type:   ARM Linux Kernel Image (uncompressed)
    Data Size:    1813268 Bytes =  1.7 MB
    Load Address: 00008000
    Entry Point:  00008000
    Verifying Checksum ... OK
 OK
 
 Starting kernel ...
 
 arg:netconsole=6666@192.168.11.150/,@192.168.11.149/ root=/dev/sda2 rw
 Uncompressing Linux................................................................................
 ........................................ done, booting the kernel.
 
 Debian GNU/Linux lenny/sid
 LS-GL.sundays.dip.jp login:


#navi(../)